summaryrefslogtreecommitdiff
path: root/doc
diff options
context:
space:
mode:
Diffstat (limited to 'doc')
-rw-r--r--doc/release.cli39
1 files changed, 31 insertions, 8 deletions
diff --git a/doc/release.cli b/doc/release.cli
index eecd155..2569a7d 100644
--- a/doc/release.cli
+++ b/doc/release.cli
@@ -163,7 +163,7 @@ distribution from \c{etc/stage} and add the pre-distributed packages
\ul|
- \li|Install guide: 1 & 2.|
+ \li|Install guide: 1 & 2 (also review build2-toolchain commit log).|
\li|Toolchain introduction: 1, 2 & 3 (use \c{intro} script output for 2).|
@@ -353,8 +353,9 @@ distribution from \c{etc/stage} and add the pre-distributed packages
git -C build2-toolchain commit --amend # \"Change version to X.Y.Z\"
\
- Note that \c{libbuild2-hello} is independently versioned but may still
- need to update minimum \c{build2} version requirements (see below).
+ Note that \c{libbuild2-*} modules (e.g., \c{libbuild2-hello}) are
+ independently versioned but may still need to update minimum \c{build2}
+ version requirements (see below).
|
@@ -363,7 +364,21 @@ distribution from \c{etc/stage} and add the pre-distributed packages
\li|Regenerate documentation in each package.|
\li|Upgrade all dependencies in configure-only mode by executing
- \c{etc/upgrade\ -c}.|
+ \c{etc/upgrade\ -c}.
+
+ If the \c{build2}/\c{bpkg} requirements in the manifests have been
+ bumped to the version being released, then first bootstrap the build
+ system and update \c{bpkg}/\c{bdep} (might have to hack their
+ generated \c{version.hxx} to disable constraint checking; also if you
+ forget \c{BDEP_SYNC=0} it will most likely hose the build
+ configuration).
+
+ \
+ BDEP_SYNC=0 b-boot build2/build2/
+ BDEP_SYNC=0 b bpkg/ bdep/
+ \
+
+ |
\li|Trigger regeneration of version files (might require several runs
to \"close off\"):
@@ -400,7 +415,7 @@ distribution from \c{etc/stage} and add the pre-distributed packages
|
- \li|Update \c{libbuild2-hello} if required.||
+ \li|Update \c{libbuild2-*} modules if required.||
Verify key tests pass (in particular, the \c{bdep} tests will now be running
against \c{public} services):
@@ -453,7 +468,8 @@ distribution from \c{etc/stage} and add the pre-distributed packages
\h#queuing|Queue|
- Prepare packages and the toolchain distribution:
+ Prepare packages and the toolchain distribution (disable extra packages
+ first if any were enabled in the \c{stage} script):
\
etc/stage -q -b
@@ -524,7 +540,12 @@ distribution from \c{etc/stage} and add the pre-distributed packages
\N|Note that the \c{queue} \c{buildtab} is shared between \c{public} and
\c{queue} builds. As a result, after this update, \c{public} build hosts
- may not have some of the new (or renamed) build machines.|
+ may not have some of the new (or renamed) build machines.
+
+ This also means that if the \c{buildtab} contains anything new (options,
+ etc) that are incompatible with \c{public}, then they should only be
+ enabled later, when upgrading \c{public} \c{buildtab} (make a note if
+ that's the case).|
Adjust \c{stage} and \c{devel} build host configurations (both \c{*-config}
and hardware classes) to enable the \c{queue} toolchain. Shift most
@@ -605,6 +626,8 @@ distribution from \c{etc/stage} and add the pre-distributed packages
~/work/build2/buildos/upload-machine <host> .../new-ver .../old-ver
\
+ Finally, add any new machines.
+
Uncomment the \c{public} toolchain in the build host configuration and
regenerate. The only remaining step is to reboot (not yet):
@@ -635,7 +658,7 @@ distribution from \c{etc/stage} and add the pre-distributed packages
Note that once published, the existing install instructions/download
links are no longer usable, so do not linger (in fact, may make sense
to update Download and Install pages before publishing packages and
- sync only them immediately after).
+ only sync them immediately after).
\h#start-public|Start \c{public} builds|