diff options
Diffstat (limited to 'doc/manual.cli')
| -rw-r--r-- | doc/manual.cli | 30 |
1 files changed, 15 insertions, 15 deletions
diff --git a/doc/manual.cli b/doc/manual.cli index fef1b89..a5d426f 100644 --- a/doc/manual.cli +++ b/doc/manual.cli @@ -314,10 +314,10 @@ For example: 1~1.2.3-a.1+2 \ -The \i{major}, \i{minor}, and \i{patch} should be numeric values between 0 and -999 and all three cannot be zero at the same time. For initial development it -is recommended to use 0 for \i{major}, start with version \c{0.1.0}, and change -to \c{1.0.0} once things stabilize. +The \i{major}, \i{minor}, and \i{patch} should be numeric values between \c{0} +and \c{999} and all three cannot be zero at the same time. For initial +development it is recommended to use \c{0} for \i{major}, start with version +\c{0.1.0}, and change to \c{1.0.0} once things stabilize. In the context of C and C++ (or other compiled languages), you should increment \i{patch} when making binary-compatible changes, \i{minor} when @@ -381,13 +381,13 @@ is uniquely identified by the snapshot sequence number (\i{snapsn}) and snapshot id (\i{snapid}). The \i{num} component has the same semantics as in the final pre-releases -except that it can be 0. The \i{snapsn} component should be either the special -value '\c{z}' or a numeric, non-zero value that increases for each subsequent -snapshot. It must fit into an unsigned 64-bit integer. The \i{snapid} -component, if present, should be an alpha-numeric value that uniquely -identifies the snapshot. It is not required for version comparison (\i{snapsn} -should be sufficient) and is included for reference. It must not be longer -than 16 characters. +except that it can be \c{0}. The \i{snapsn} component should be either the +special value '\c{z}' or a numeric, non-zero value that increases for each +subsequent snapshot. It must fit into an unsigned 64-bit integer. The +\i{snapid} component, if present, should be an alpha-numeric value that +uniquely identifies the snapshot. It is not required for version comparison +(\i{snapsn} should be sufficient) and is included for reference. It must not +be longer than 16 characters. Where do the snapshot sn and id come from? Normally from the version control system. For example, for \c{git}, \i{snapsn} is the commit date (as UNIX @@ -447,8 +447,8 @@ E - final (0) / snapshot (1) If the \i{DDDE} value is not zero, then it signifies a pre-release. In this case one is subtracted from the \i{AAABBBCCC} value. An alpha number is stored -in \i{DDD} as is while beta \- incremented by 500. If \i{E} is 1, then this is -a snapshot after \i{DDD}. +in \i{DDD} as is while beta \- incremented by \c{500}. If \i{E} is \c{1}, then +this is a snapshot after \i{DDD}. For example: @@ -1227,8 +1227,8 @@ mxx{std-core}@./: cc.module_name = std.core When C++ modules are enabled and available, the build system makes sure the \c{__cpp_modules} feature test macro is defined. Currently, its value is -201703 for VC and 201704 for GCC and Clang but this will most likely change in -the future. +\c{201703} for VC and \c{201704} for GCC and Clang but this will most likely +change in the future. One major difference between the current C++ modules implementation in VC and the other two compilers is the use of the \c{export module} syntax to identify |