// file : doc/manual.cli // copyright : Copyright (c) 2014-2017 Code Synthesis Ltd // license : MIT; see accompanying LICENSE file "\name=build2-package-manager-manual" "\subject=package manager" "\title=Package Manager" // NOTES // // - Maximum
 line is 70 characters.
//

"
\h0#preface|Preface|

This is the preface.

\h1#package-version|Package Version|

The \c{bpkg} package version format tries to balance the need of accommodating
existing software versions on one hand and providing a reasonably
straightforward comparison semantics on another. For some background on this
problem see \cb{deb-version(1)} and the \l{http://semver.org Semantic
Versioning} specification.

Note also that if you are strating a new project that will use the \c{build2}
toolchain, then it is strongly recommended that you use the \i{standard
versioning} scheme which is a more strictly defined subset of semanic
versioning and that allows automation of many version management tasks. See
\l{https://build2.org/build2/doc/build2-build-system-manual.xhtml#module-version
Version Module} for details.

The \c{bpkg} package version has the following form:

\
[~][-][+]
\

The \i{epoch} part should be an integer. It can be used to change to a new
versioning scheme that would be incompatible with the old one. If not
specified, then \i{epoch} defaults to \c{0}.

The \i{upstream} part is the upstream software version that this package
is based on. It can only contain alpha-numeric characters and \c{'.'}. The
\c{'.'} character is used to separate the version into \i{components}.

The \i{prerel} part is the upstream software pre-release marker, for example,
alpha, beta, candidate, etc. Its format is the same as for \i{upstream} except
for two special values: the absent \i{prerel} (for example, \c{1.2.3})
signifies the maximum or final release while the empty \i{prerel} (for
example, \c{1.2.3-}) signifies the minimum or earliest possible
release. [Note: the minimum release is intended to be used for version
constraints (for example, \c{libfoo < 1.2.3-}) rather than actual releases.]

The \i{revision} part should be an integer. It is used to version package
releases that are based on the same upstream versions. If not specified, then
\i{revision} defaults to \c{0}.

Version \c{0-} (least possible version) is reserved and specifying it
explicitly is illegal. [Note: explicitly specifying this version does not make
much sense since \c{libfoo < 0-} is always false and \c{libfoo > 0-} is always
true. In the implementation this value is used as a special empty version.]

Version \c{0} (with a potential revision, for example, \c{0+1}, \c{0+2}) is
used to signify a \i{stub package}. A stub is a package that does not contain
source code and can only be \"obtained\" from other sources, for example, a
system package manager. Note that at some point a stub may be converted into a
full-fledged package at which point it will be assigned a \"real\" version.
It is assumed that this version will always be greater than the stub version.

When displaying the package version or when using the version to derive the
file name, zero \i{epoch} and \i{revision} are omitted (even if they were
explicitly specified, for instance, in the package manifest). For example,
\c{0~1.2.3+0} will be used as \c{libfoo-1.2.3}.

[Note: this versioning scheme and the choice of delimiter characters (\c{~-+})
is meant to align with semantic versioning.]

Some examples of versions:

\
1.2.3
1.2.3-a1
1.2.3-b2
1.2.3-rc1
1.2.3-alpha1
1.2.3-alpha.1
1.2.3-beta.1
1.2.3+1
1~1.2.3
1~1.2.3-alpha.1+3
\

The version sorting order is \i{epoch}, \i{upstream}, \i{prerel}, and,
finally, \i{revision}. The \i{upstream} and \i{prerel} parts are compared from
left to right, one component at a time, as described next.

To compare two components, first the component types are determined.  A
component that only consists of digits is an integer. Otherwise, it is a
string. If both components are integers, then they are compared as
integers. Otherwise, they are compared lexicographically and case-
insensitively. [Note: the reason for case-insensitive comparsion is Windows
file names.]

A non-existent component is considered 0 if the other component is an integer
and an empty string if the other component is a string.  For example, in
\c{1.2} vs \c{1.2.0}, the third component in the first version is 0 and the
two versions are therefore equal. As a special exception to this rule, an
absent \i{prerel} part is always greater than any non-absent part. [Note: and
thus making the final release always older than any pre-release.]

This algorithm gives correct results for most commonly-used versioning
schemes, for example:

\
1.2.3 < 12.2
1.alpha < 1.beta
20151128 < 20151228
2015.11.28 < 2015.12.28
\

One notable versioning scheme where this approach gives an incorrect result is
hex numbers (consider \c{A} vs \c{1A}). The simplest work around is to convert
such numbers to decimal. Alternatively, one can fix the width of the hex
number and pad all the values with leading zeros, for example: \c{00A} vs
\c{01A}.

It is also possible to convert the \i{upstream} and \i{prerel} parts into a
\i{canonical representation} that will produce the correct comparison result
when always compared lexicographically and as a whole. [Note: this can be
useful, for example, when storing versions in the database which would
otherwise require a custom collation implementation to obtain the correct sort
order.]

To convert one of these parts to its canonical representation, all its string
components are converted to the lower case while all its integer components
are padded with leading zeros to the fixed length of \c{8} characters, with
all trailing zero-only components removed. Note that this places an
implementation limit on the length of integer components which should be
checked by the implementation when converting to the canonical
representation. [Note: the \c{8} characters limit was chosen to still be able
to represent components in the \c{20151128} (date) form while not (visually)
bloating the database too much.] As a special case, the absent \i{prerel} part
is represented as \c{'~'}. [Note: since the ASCII code for \c{'~'} is greater
than any other character that could appear in \i{prerel}, such a string will
always be greater than any other representation.] The empty \i{prerel} part is
represented as an empty string.

Note that because it is no possible to perform a reverse conversion without
the possibility of loss (consider \c{01.AA.BB}), the original parts may also
have to be stored, for example, for display, to derive package archive names,
etc.

[Note: in quite a few contexts the implementation needs to ignore the
\i{revision} part. For example, this is needed to implement the semantics of
newer revisions of packages replacing their old ones since we do not keep
multiple revisions of the same upstream version in the same respository. As a
result, in the package object model, we have a version key as just {\i{epoch},
\i{upstream}, \i{prerel}} but also store the package revision so that it can
be shown it to the user, etc.]
"